| Last Modified: 11-29-2007 | 1.6 A | |
| Service Category: Power Source/Network | Section: Battery/Charging | |
| Model Year: 2008 | Model: Sequoia | Doc ID: RM00000189100VX |
| Title: 3UR-FE BATTERY / CHARGING: GENERATOR: REASSEMBLY (2008 Sequoia) | ||
REASSEMBLY
1. INSTALL GENERATOR DRIVE END FRAME BEARING (130 A, 150 A Type)
(a) Using SST and a press, press in a new bearing.
SST: 09950-60010
09951-00470
SST: 09950-70010
09951-07100
|
(b) Install the retainer plate with the 4 screws. Torque: 2.3 N·m (23 kgf·cm, 20 in·lbf) |
2. INSTALL GENERATOR DRIVE END FRAME BEARING (180 A Type)
(a) Using SST and a press, press in a new bearing.
SST: 09950-60010
09951-00500
SST: 09950-70010
09951-07100
|
|
(b) Install the retainer plate with the 4 screws. Torque: 3.0 N·m (30 kgf·cm, 26 in·lbf) |
3. INSTALL GENERATOR ROTOR ASSEMBLY
|
(a) Place the drive end frame on the pulley. |
(b) Install the rotor to the drive end frame.
4. INSTALL GENERATOR COIL ASSEMBLY (130A,150A TYPE)
|
(a) Place the generator washer on the rotor. |
|
(b) Using a 22 mm socket wrench and a press, slowly press in the coil assembly. |
|
(c) Install the 4 bolts. Torque: 5.8 N·m (59 kgf·cm, 51 in·lbf) |
5. INSTALL GENERATOR COIL ASSEMBLY (180A TYPE)
|
|
(a) Place the generator washer on the rotor. |
|
|
(b) Using a 22 mm socket wrench and a press, slowly press in the coil assembly. |
|
|
(c) Install the 4 bolts. Torque: 7.5 N·m (76 kgf·cm, 66 in·lbf) |
6. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY
|
(a) While pushing the 2 brushes toward the inside of the brush holder, insert a pin (diameter: 1.0 mm (0.0394 in.)) into the brush holder hole. |
|
(b) Install the generator brush holder with the 2 screws. Torque: 1.8 N·m (18 kgf·cm, 16 in·lbf) |
(c) Pull out the pin from the generator brush holder.
7. INSTALL GENERATOR REAR END COVER
|
(a) Install the terminal insulator to the generator rectifier end frame. NOTICE:
Pay attention to the mounting orientation of the terminal insulator. |
|
(b) Install the end cover with the 3 nuts. Torque: 4.6 N·m (47 kgf·cm, 41 in·lbf) |
8. INSTALL GENERATOR PULLEY
SST: 09820-63011
09820-06010
09820-06021
|
SST 1-A and B |
09820-06010 |
|
SST 2 |
09820-06021 |
(a) Clamp the generator housing stay in a vice.
(b) Install the pulley onto the rotor shaft by tightening the pulley nut by hand.
(c) Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise to the specified torque.
Torque: 39 N·m (398 kgf·cm, 29 ft·lbf)
NOTICE:
Check that SST is secured to the rotor shaft.
|
(d) Insert SST 2, and attach the pulley nut to SST 2. |
|
(e) Tighten the pulley nut by turning SST 1-A in the direction shown in the illustration. Torque: 133 N·m (1351 kgf·cm, 98 ft·lbf) HINT:
Hold the adjustable wrench against the vice and tighten the nut securely. |
(f) Remove the generator from SST 2.
|
(g) Turn SST 1-B, and remove SST 1-A and B. |
(h) Turn the pulley and check that the pulley moves smoothly.
|
|